3D-printed parts and food contact: what EU rules and filament makers say

By Sina Esfahani, OmniTechs · Published 22 November 2026

No filament makes a 3D-printed part food safe by itself. EU law attaches the duty to the finished article and to the business that places it on the market: Regulation (EC) No 1935/2004 sets the general safety requirement, and for plastics Regulation (EU) No 10/2011 adds a list of authorised substances, migration limits and a written declaration of compliance. None of the five printer and filament makers read for this page claims that its filament makes a print food safe; those that go into detail point to layer gaps, colourants, the nozzle and cleaning.

This page is a reading guide to published rules and manufacturer statements as read on 22 November 2026, not legal advice; the official text decides.

What the rules and the makers require or state

Food contact: what each source requires or states

Requirements of three EU regulations and statements of the Dutch authority NVWA, EFSA and five makers on food contact, read from their own pages on 22 November 2026.
SourceWhat it requires or statesApplies to
Regulation (EC) 1935/2004, Article 3Made so that nothing transfers to food in quantities that endanger health, change the food unacceptably or spoil taste and smell; labelling must not misleadEvery material and article intended for food contact, in its finished state
Regulation (EC) 1935/2004, Article 15(1)(a) and 15(2)Sold before it touches food: the words for food contact, a specific use or the Annex II symbol; not obligatory for articles that by their characteristics are clearly intended for food contactThe business placing the article on the market; shown at retail
Regulation (EC) 1935/2004, Article 15(1)(b) to (d)Instructions for safe use where necessary, the name and address of the responsible manufacturer, processor or seller, and identification for traceability; these remain required when the indication above is notThe business placing the article on the market; shown at retail
Regulation (EC) 1935/2004, Article 17Traceability at all stages: each business can identify the businesses it received from and the businesses it supplied toMaterial maker, article maker and seller
Regulation (EC) 2023/2006A documented quality assurance system, quality control and records of specifications and processingAll stages of manufacture, processing and distribution after the starting substances
Regulation (EU) 10/2011, Articles 4 to 6Marketed only if all of the above is met; substances must be on the Union list unless an Article 6 derogation applies, such as colourants and solvents under national lawMakers of plastic materials and of plastic articles
Regulation (EU) 10/2011, Articles 11 and 12Specific limits per substance and an overall limit on the non-volatile substances released, usually tested with food simulantsThe material or article as it will be used
Regulation (EU) 10/2011, Articles 15 and 16, Annex IVA written declaration of compliance with issuer, article, date and conditions of use, backed by documents kept for the authoritiesMaterial maker and article maker, towards business customers; not the retail stage
NVWAProducers and importers are themselves responsible for safe products; the NVWA does not check products before they reach the marketBusinesses in the Netherlands
EFSAAssesses the safety of substances; its advice informs the legal migration limitsSubstances, not individual articles
BASF 3D Printing Solutions, Ultrafuse PLA statement of 2022Raw materials suitable for food contact under 10/2011; testing whether the final printed product complies rests with the user of the filamentFilament maker and whoever prints the article
PrusaIts filaments have no certification; print food-contact objects with them only for personal use, not for saleFilament maker and whoever prints the article
PolymakerA food-contact compliant filament does not automatically make the finished print food safeFilament maker and whoever prints the article
Bambu Lab, PLA BasicNot food-grade; avoid using finished prints for food storage or contactFilament maker
FormlabsCompliant with does not mean approved; check the data sheet for a certificatePrinter maker

Common claims next to the sources

Common food-contact claims about 3D prints checked against sources

Frequent claims about food-safe 3D prints next to what EU regulations and the makers themselves state, read from their own pages on 22 November 2026.
Common claimWhat the sources actually saySource
PLA is food safeThe PLA material itself is food-safe, but not recommended for items in direct contact with food because print grooves can support bacterial growthPrusa
PLA is food safeThis PLA is not food-gradeBambu Lab, PLA Basic
PETG is food safePETG is considered food-safe, but not recommended for dishes or other items in direct contact with foodPrusa
PETG is food safeSome variants are FDA-approved for food contact; certifications should always be verifiedPolymaker
A food-safe filament gives a food-safe printNo: the finished print is judged on geometry, surface, hardware contamination, additives, cleaning and intended usePolymaker
The maker's statement covers my printThe responsibility to test the final printed product rests with the user of the filamentBASF 3D Printing Solutions
The colour makes no differencePigments can be unsafe even in a safe polymer; the Union list excludes colourants, which fall under national lawPrusa; Regulation (EU) 10/2011
The nozzle makes no differenceBrass nozzles can contain lead; use a dedicated stainless steel nozzlePrusa; Formlabs
A coating makes a print food safeCertification and correct application of the coating are not enough on their own: a coating can degrade and expose the surface underneath, so the finished article still has to be assessed for its intended usePolymaker; Formlabs
Dishwasher safePrints may deform, leach or degrade in a dishwasher, and bacteria in crevices can survive it; Prusa excludes the dishwasher for its epoxy-coating process and Formlabs says not all coatings are dishwasher safe, so a coating needs its own evidence for that usePolymaker; Formlabs; Prusa
Resin prints are food safeNo resin or resin print is food safe by defaultFormlabs

A food-contact claim is about the finished article

Regulation 1935/2004 applies to materials and articles "in their finished state" that are intended to touch food or can reasonably be expected to. Its central rule, Article 3, is about what transfers from that article into food under normal or foreseeable use. A spool of filament is not yet that article; the cup, scoop or mould printed from it is.

For plastics, Regulation 10/2011 turns the rule into a chain of evidence. Monomers, other starting substances and additives must come from the Union list, unless one of the derogations in Article 6 applies; colourants, solvents and polymer production aids, for example, are left to national law. Migration is limited per substance and overall, and is tested under standardised time and temperature conditions that represent the intended use. Each business in the chain passes a declaration of compliance to the next, up to but not including the retail stage, as the European Commission puts it. That declaration names the conditions of use it was verified for: the type of food, the time and temperature of contact, and the ratio of contact surface to volume.

The practical point is that a filament maker's statement and the declaration for a printed article are two different documents. BASF's statement for Ultrafuse PLA is explicit that the company is not the manufacturer of the final printed product. The makers explain why: the material passes through a hot end and a nozzle, can pick up residue of what was printed before, and ends as a layered surface. Separately, Regulation 2023/2006 requires every business in the manufacturing chain, including the one that makes the article, to run a documented quality assurance system.

None of the three regulations mentions 3D printing; a text search finds neither the term nor additive manufacturing. They are written by material and intended use, not by production technique. In the Netherlands the Warenwet decree and regulation on packaging and consumer articles apply as well, and the NVWA supervises afterwards: it does not approve products before sale.

What makers say about layers, nozzles, colourants and coatings

The makers describe four weak points of filament printing. Layer lines leave grooves that trap residue and are hard to clean; Prusa gives bacterial growth in those grooves as its main reason not to recommend printed tableware, and Polymaker describes the same mechanism. The hot end matters: Prusa and Formlabs warn against brass nozzles because the alloy can contain lead, and Polymaker adds that a nozzle can carry over material from earlier prints. Colourants and additives are separate from the base polymer: Prusa lists the colours its pigment supplier considers safe and still says it holds no certification. Coatings are presented as a way to close the surface, with warnings attached. Prusa states that all epoxy resins are toxic in liquid form and cautions against uncertified resins, Formlabs that a coating does not guarantee safety over prolonged use.

How this page was compiled and where it stops

The regulation texts were read in the consolidated versions of 27 March 2021 (1935/2004) and 16 March 2025 (10/2011), and the original text of 2023/2006. The European Commission lists two 2026 amendments to Annex I of Regulation 10/2011 that the consolidated version may not yet contain. No limit values are reproduced. The Dutch decree and regulation were read only through the NVWA's summary. Maker statements are their own and can change; the BASF statement dates from 13 May 2022 and says it expires upon any regulatory change.

What a buyer should ask for

  1. Describe the use in writing. Which food, hot or cold, for how long, and how the part will be cleaned. These are the conditions a declaration is verified for.

  2. Ask for the declaration of compliance for the article. A business buyer can ask for a declaration that names the printed article, the issuer and the date, not only a filament data sheet.

  3. Ask which filament grade and colour was used. Request the maker's food-contact statement for that grade and colour, and check its date.

  4. Ask how the part is made. Which nozzle, what else runs on that printer, and what the supplier's quality system records.

  5. Ask about any coating. A coating needs its own food-contact evidence and its own limits of use, and it does not replace the assessment of the finished article.

  6. Check the label on a consumer product. An article should carry the words for food contact, a stated use or the symbol, unless its characteristics make clear that it is intended for food contact; Article 15(2) exempts such articles from that indication only. In every case expect instructions where needed and the name and address of the responsible business. The NVWA gives the Dutch wording as "geschikt om met levensmiddelen in contact te komen".

If a supplier cannot answer these, the claim is not supported. Polymaker's own advice for parts that must touch food is to treat the print as a prototype or a mould, not as the final food-contact surface.

Where OmniTechs stands

OmniTechs states its position on its public pages. The page on 3D printed replacement parts says that parts in contact with food are assessed separately and declined when not responsible. The guide to measuring a replacement plastic part says food-contact applications require an appropriate separate assessment, and the kitchen accessories collection makes no blanket food-safe or heat-resistant claim.

For material questions that do not involve food, start with choosing a 3D printing material. The guide to 3D-printed vases and watertight inserts takes the same approach to water: a separate, tested insert takes over the critical function.