How to measure a desk for a cable grommet, clamp-on holder or under-desk tray

By Sina Esfahani, OmniTechs · Published 22 November 2026

Measure five things: the thickness of the desktop where the part goes, the shape of the edge and what sits behind it, the diameter of any existing hole, the distance to the frame, a drawer or the wall, and the largest plug that has to pass. The plug, not the cable, decides the opening, and the size of the hole is not the size of the grommet's visible collar, the flange. Fill in the sheet below and test with cardboard before you order.

What you need

  • Calipers for thickness, hole and plugs

  • A steel ruler or tape measure in millimetres

  • A torch and a phone camera

  • Cardboard, scissors and a pencil

Desktop thickness and the edge

Measure the thickness with calipers at the place where the holder will sit, at two points. An edge strip or a lip can make the edge thicker than the panel behind it, so note the shape as well: square, rounded, bevelled or with a lip. Then measure how far in from the edge the top and the underside stay flat.

Clamp makers ask for the same facts. BenQ's set-up checklist for its monitor arm wants the desk edge flat within the first 2.5 cm and tells users to check for support beams within 5 cm of the edge. Ranges differ per product: BenQ gives 1.7 to 5 cm tabletop thickness for that clamp, Kensington 10 to 85 mm for one of its arms. A printed holder is drawn around your desk, so your own reading is the starting point.

Behind the edge: frame, drawer and wall

Look under the desk with the torch. Measure from the edge to the first thing a clamp would meet, such as a frame rail, a crossbar, a drawer or a cable tray, and how far it hangs below the underside. That is the usable clamp depth. For a part at the back, measure the gap between desk and wall. On a height-adjustable desk, check what the part passes when the desk moves.

An existing grommet hole

Measure the hole in the bare desktop, not the collar. Lift the insert out, measure the diameter in two directions and take the desktop thickness inside the hole.

Listings for common sizes show three different numbers. Hettich desk grommets at Hornbach have a 60 mm drill diameter with a 68 mm outside diameter, and 80 mm with 88 mm. Moderix grommets at B&Q list a 60 mm hole with a 70 mm outer and a 54 mm inner diameter, and an 80 mm hole with 90 mm and 74 mm. So note the hole, the space around it for a collar, and what sits directly underneath.

Cables and plugs

Count the cables and measure the largest plug: width, height and length including the stiff part of the cable. That plug has to pass the opening, unless the part has a slot at the side where cables are laid in. A fitted grommet narrows the hole, as the inner diameters above show. Measure cable diameters only for clips and slots.

Under-desk tray and the surface

For a tray, measure the free length between legs or frame rails, the depth from the back edge to the nearest obstruction and the height you can give up above your knees or a drawer. Say how it may be fixed: screwed into the underside, clamped, or hung on the frame. List what goes in it, with sizes and weight.

Note the surface too: laminate, veneer, oiled wood or glass, and which faces the part may touch. Say whether you want pads and whether anything may be glued or screwed.

What to measure

What to measure on a desk

Ten measurements to take from a desk before requesting a custom cable grommet, clamp-on holder or under-desk tray, with the method and the reason for each.
MeasurementHowWhy it matters
Desktop thickness at the edgeCalipers at two points where the part goesSets the opening of a clamp-on holder
Edge shapeSquare, rounded, bevelled or lipped, and the flat partA clamp needs a flat seat above and below
Clamp depthEdge to the first rail, drawer or tray underneathLimits how far a clamp can reach in
Obstruction heightHow far that rail or drawer hangs below the topDecides whether a part can pass under it
Hole diameterBare hole in two directions, insert removedThe body follows the hole, not the collar
Space around the holeHole edge to wall, desk edge and objectsThe collar is wider than the hole
Largest plugWidth, height and length with the stiff cable endThe plug decides the opening
Cable diameterCalipers on each cable typeSets clips and slots
Free space under the deskLength, depth and height between frame partsSets the size of a tray
SurfaceMaterial, finish and faces the part may touchDecides padding and fixing

Measurement sheet

Desk measurement sheet

A fill-in sheet for the sizes and choices that belong with a request for a custom cable grommet, clamp-on holder or under-desk tray.
ItemYour valueNote
Desktop thickness, point 1... mmAt the edge where the part goes
Desktop thickness, point 2... mmA hand's width further along
Edge shape...Square, rounded, bevelled or lipped
Flat part from the edge, top... mmBefore a bevel, rounding or object
Flat part from the edge, underside... mmBefore a rail, lip or drawer
Obstruction below the top... mmWhat it is and how far it hangs down
Gap between desk and wall... mmOnly for a part at the back
Hole diameter, two directions... × ... mmBare hole, insert removed
Desktop thickness in the hole... mmCalipers
Clear space around the hole... mmTo the nearest wall, edge or object
Largest plug... × ... × ... mmWidth, height, length
Number of cables...With the thickest cable in mm
Space for a tray... × ... × ... mmLength, depth, height
Surface and fixing...Finish, and clamp, screws or pads
Template checkpass / fail / not doneWith the date

Check with a cardboard template

  1. Fold a U shape from cardboard with the planned opening and depth of the clamp, and slide it over the edge.

  2. Cut a disc the size of the collar and lay it over the hole.

  3. Cut the planned opening in cardboard and pass the largest plug through with its cable attached.

  4. Hold a tray outline under the desk, then sit down and open the drawer.

A template shows position and obstructions, not the printed fit. The tolerances and clearance guide explains why there is no universal clearance for every print.

Common mistakes

  • Measuring the collar instead of the hole

  • Measuring thickness on the edge strip only

  • Sizing the opening for the cable instead of the plug

  • Forgetting the frame rail behind the edge

  • Assuming screws into the underside are allowed

What to send with a request

  • The filled-in measurement sheet

  • Photos of the top, the edge from the side with a ruler, and the underside

  • What the part must hold, with size and weight

  • How it may be fixed, and what is not allowed on the surface

  • The cables and plugs that pass through

  • Colour and quantity

Ready-made desk items are in the 3D-printed desk organisers. For a part drawn around your desk, send the sheet through custom home accessories; fitting it at your home is not included automatically. For the inside of a drawer, see measure usable drawer space for a custom organiser.