How to measure a plant pot for a custom 3D-printed planter, cover pot or saucer

By Sina Esfahani, OmniTechs · Published 22 November 2026

Measure the pot that goes inside, not the plant: the outer diameter of the rim, the outer diameter of the base, the vertical height and how the side runs between them. For a cover pot, the widest point of the nursery pot decides whether it fits and its height decides how you lift it out. For a saucer, the base decides.

The size on the label is not that measurement. UK plant seller Gardeners Dream lists 6, 12, 15, 19 and 23 cm as its most common nursery pots, measured as the diameter at the top. Jacksons Nurseries warns that sizes are only a guide, because exact measurements vary between pot manufacturers. Its table gives a 2 litre pot as 17 cm across the top, 12 cm across the base and 13 cm high.

What you need

  • A rigid ruler with a millimetre scale

  • A flexible tape measure

  • Calipers, if you have them

  • Two straight-sided books

  • Thin cardboard, scissors and a pencil

Calipers read a diameter directly, but only as far as the jaws open. For a wider pot, stand it between the two books, slide them against the widest point and measure the gap with the ruler. A tape laid around the pot without pulling gives the circumference: divide it by 3.14 for the diameter, as a check.

Measure the pot in four steps

  1. Rim. Measure the outer diameter across the top, lip included, in two directions at right angles. A thin plastic pot gives way, so write down both. Note the thickness and height of the lip.

  2. Base. Measure the outer diameter of the part that stands on the table, or the circle around the feet.

  3. Height. Lay the ruler flat across the rim and measure straight down to the table, not along the sloping side.

  4. Taper. Rim, base and height describe a straight side. If the side curves or has a step, add one diameter halfway up, with its height.

The nursery pot inside a cover pot

The widest point of the nursery pot, usually the rim, has to pass the narrowest point of the cover pot. Its height decides where that rim ends up.

Retailers list these as separate figures: one IKEA cover pot has an outside diameter of 11 cm, an inside diameter of 10 cm and a maximum inner pot diameter of 9 cm. Dutch plant shop Green Bubble advises comparing the top of the nursery pot with the inner diameter of the decorative pot. So mark every figure you send as an outside or an inside size.

Then decide how the pot comes out. A rim that stands above the edge of the cover pot can be gripped. A rim level with the edge or lower needs finger room beside the pot, recesses or a raised floor. How much room to leave is a design decision: the tolerances and clearance guide explains why there is no universal clearance for every print.

Drainage, standing water and saucers

The Royal Horticultural Society says a houseplant container should always have a drainage hole and that water-filled saucers should be emptied after watering, because roots can drown when a plant sits in water for long periods. University of Illinois Extension adds: if water collects in an outer container, take the inner pot out and drain it.

A cover pot or saucer is where that water ends up. Do not assume a printed one is watertight. That depends on design, material, print settings and use, as the guide to 3D-printed vases and watertight inserts explains, and OmniTechs does not promise it as standard. Say whether water will stand in the print or a separate watertight dish goes inside.

Size a saucer from the base, not from the label: its flat floor has to take the base of the pot or the circle of its feet.

What to measure

What to measure on a plant pot

Eight measurements to take from a plant pot before requesting a custom planter, cover pot or saucer, with the method and the reason for each.
MeasurementHowWhy it matters
Rim outer diameterAcross the top in two directions, lip includedWidest point, so it decides whether the pot passes the opening
Base outer diameterAcross the part that stands on the tableSets the saucer floor and the floor of a cover pot
HeightRuler across the rim, straight down to the tableDecides where the rim sits and how the pot lifts out
Mid-height diameterOnly for a curved or stepped side, with its heightDescribes a taper that is not straight
Rim lipThickness and height of the rolled edgeThe lip can rest on or catch the cover pot edge
Out-of-roundDifference between the two rim readingsA flexible pot is not a perfect circle
Existing cover potOpening, floor diameter and inside depthNeeded when the print has to fit inside it
DrainageHoles in the base and where the water goesDecides whether water stands in the print

Measurement sheet

Plant pot measurement sheet

A fill-in sheet for the sizes and choices that belong with a request for a custom planter, cover pot or saucer.
ItemYour valueNote
Size on the label...For reference only
Rim outer diameter, direction 1... mmLip included
Rim outer diameter, direction 2... mmAt a right angle to the first
Base outer diameter... mmOr the circle around the feet
Height, table to rim... mmVertical, not along the side
Mid-height diameter... mm at ... mmOnly for a curved or stepped side
Lip thickness and height... × ... mmCalipers if possible
Measured with...Ruler, tape or calipers
Pot material...Rigid or flexible
Drainage holesyes / noCount them if they matter
Rim position wantedabove / level / belowCompared with the cover pot edge
Water in the printnone / liner / must hold waterAgreed and tested separately
Template checkpass / fail / not doneWith the date

Check with a cardboard template

Cut a hole with the planned opening diameter in cardboard and lower it over the pot: it should pass the rim without force. Cut a disc the size of the planned saucer floor and stand the pot on it. A template checks size and handling, not the printed fit.

Common mistakes

  • Using the label size as the measurement

  • Measuring height along the sloping side

  • Measuring a flexible pot in one direction only

  • Sizing a saucer from the rim instead of the base

  • Assuming the print holds water

What to send with a request

  • The filled-in measurement sheet

  • A photo from the side with a ruler in the frame, and one from above

  • What you want made: a cover pot, a planter with drainage or a saucer

  • Where the rim should sit and how you lift the pot out

  • Indoors or outdoors, and whether water will stand in the print

  • Colour and quantity

The 3D-printed planters show per product whether a saucer or inner pot is included. For a design around your own pot, send the sheet through custom home accessories. For a drawer, see measure usable drawer space for a custom organiser.