3D printing or injection moulding: where is the break-even quantity?

By Sina Esfahani, OmniTechs · Published 22 November 2026

For a small part that we print for €8.28 per piece at 100 pieces, injection moulding becomes the cheaper route between about 420 and 1,130 pieces. That holds when a simple mould costs €3,000 to €8,000 and each moulded piece €1.20, figures published by Dutch moulders. With a complex mould of €30,000 the same sum gives about 4,240 pieces.

All amounts exclude VAT. The print prices come from our public cost page, reviewed on 9 November 2026. The moulding figures were read on 22 November 2026 on the pages of the moulders and platforms named below. We print and do not mould, so that side is their published guidance, not our quote.

The formula

Injection moulding has a one-off cost, the mould (also called tooling), and a low cost per piece. Printing has no mould and a higher cost per piece. Both routes cost the same at quantity Q where:

mould + Q × moulded cost per piece = Q × printed price per piece

Rearranged: Q = mould ÷ (printed price per piece − moulded cost per piece).

Two details matter:

  • The printed price per piece falls as the quantity rises. Use the price for the quantity you are considering, not the single-piece price.

  • Round Q up: the result is the first quantity at which moulding costs less in total.

What a mould and a moulded piece cost, by source

Four Dutch moulders publish a starting price of about €3,000 for a simple mould. Their upper ends, for large or complex moulds, run from €30,000 or more at Gebrema to €150,000 at Wicro. International platforms publish in US dollars, left unconverted here.

Published mould and piece costs by source

Figures as published by each source, read on 22 November 2026; amounts in the stated currency, VAT not stated by the sources.
SourceCurrencyMouldMoulded piecePage date
QDPEURFrom 3,000, mostly 3,000 to 5,000, up to 60,000Not publishedNot shown
Wicro GroupEURFrom 3,000 simple, up to 150,000Not publishedNot shown
GebremaEUR3,000 to 8,000 simple, 30,000 or more complexA few cents to a few euros7 Aug 2026
FlinQ PlasticsEURAbout 3,000 to 50,000 or moreOften 0.50 to 5, example 1.2028 Feb 2022
Protolabs NetworkUSDAluminium from about 3,000 to 5,0001 to 5 at 500 to 10,000 partsNot shown
ProtolabsUSDFrom 1,495Not publishedNot shown
FormlabsUSD2,000 to 5,000 aluminium, 5,000 to 100,000 for 10,000 or more unitsExample 2.00 at 5,000 partsNot shown
XometryUSDUp to 10,000 for 1,000 to 2,000 small parts, up to 100,000Not published20 Jul 2026

The sources do not fully agree. The Protolabs Network guide gives $3,000 to $5,000 for an aluminium mould in its cost section and $250 to $1,000 for simpler moulds in its introduction. None of the moulders' pages states VAT; we read their figures as excluding VAT, so confirm that in your own quote.

What the printed part costs, by quantity

Our cost page publishes one worked example by quantity: a PLA print of 50 g and 4 print hours, from a print-ready file, shipped within the Netherlands. Preparation, the order minimum, packaging (€4) and shipping (€6) count once per order. Identical pieces receive a quantity discount on material, print time and plates of 5% from 25 pieces, 10% from 50 and 15% from 100.

Printed price per piece by quantity, example part

OmniTechs published prices for a 50 g, 4-hour PLA print, reviewed 9 November 2026; totals excluding VAT are calculated from the published totals including 21% VAT.
PiecesPer piece excl. VATPer piece incl. VATTotal excl. VATTotal incl. VAT
1€30.00€36.30€30.00€36.30
10€9.66€11.69€96.60€116.89
25€8.58€10.39€214.57€259.63
50€8.38€10.14€418.94€506.92
100€8.28€10.01€827.66€1,001.47

This price is for that example part only. Replace it with your own quote before you decide anything about your part.

At every published quantity printing is cheaper: 100 pieces cost €827.66, against €3,000 + 100 × €1.20 = €3,120 with the cheapest mould. The break-even therefore lies above 100 pieces, where we publish no price, so the calculation below holds €8.28 constant. Above 200 pieces of this part (10 kg and 800 print hours) the published lower bands of €36 per kg and €0.88 per hour apply to the extra material and hours. A quote for a larger run can therefore come out lower, which raises the break-even.

Break-even for three mould prices

The moulded cost per piece is €1.20, the figure in FlinQ Plastics' own worked example. The table names the source of each mould price; all three are in the range the moulders give for a simple mould.

Break-even quantity for three mould prices

Calculated on 22 November 2026 from the published figures above; all amounts exclude VAT and the printed price is held at €8.28 per piece.
ScenarioMouldMoulded pieceBreak-evenPrinting totalMoulding total
Low: QDP and Wicro start€3,000€1.20424 pieces€3,510.72€3,508.80
Middle: top of QDP's usual range€5,000€1.20707 pieces€5,853.96€5,848.40
High: top of Gebrema's simple range€8,000€1.201,130 pieces€9,356.40€9,356.00

The arithmetic:

  1. Low: 3,000 ÷ (8.28 − 1.20) = 3,000 ÷ 7.08 = 423.7, rounded up to 424. Printing: 424 × 8.28 = 3,510.72. Moulding: 3,000 + 424 × 1.20 = 3,508.80.

  2. Middle: 5,000 ÷ 7.08 = 706.2, rounded up to 707. Totals: 707 × 8.28 and 5,000 + 707 × 1.20.

  3. High: 8,000 ÷ 7.08 = 1,129.9, rounded up to 1,130. Totals: 1,130 × 8.28 and 8,000 + 1,130 × 1.20.

FlinQ's usual range per moulded piece is €0.50 to €5. With the €3,000 mould that puts the break-even at 386 pieces (€0.50) or 915 pieces (€5). FlinQ's example mould of €12,000 gives 1,695 pieces, and Gebrema's €30,000 for a complex mould 4,238.

These results fit the published rules of thumb. Our small-batch page calls printing the cheapest route up to a few hundred pieces. Protolabs Network names 500 units as the minimum order volume, QDP a sweet spot of 500 to 20,000 pieces per run, and Gebrema 1,000 to 5,000 pieces per year as the start of cost-efficient moulding.

What moves the break-even

Part size and print time. The printed price follows grams and hours: our published rates start at €40 per kg of PLA and €1.04 per print hour. A larger or slower part costs more per piece, so a mould pays for itself sooner. With the €3,000 mould and €1.20 per moulded piece, a print quote of €4 per piece breaks even at 1,072 pieces and one of €15 at 218.

Mould complexity. According to Protolabs Network, side-action cores for undercuts raise the mould price by 15 to 30%, at least about $1,000 to $1,500. QDP and Gebrema note that multi-cavity moulds cost more but lower the piece price in large runs.

Number of variants. Protolabs Network states that every part geometry needs its own mould; a different colour alone leaves the geometry, and so the mould, unchanged. We print variants as one batch from a list. Five different shapes of the example part's size, 200 pieces each, need five moulds: 5 × €3,000 + 1,000 × €1.20 = €16,200. Printed at €8.28 per piece that is about €8,280, plus our published preparation charge of €5 for each extra print file.

Design changes. Protolabs writes that removing metal from a finished mould is relatively easy, while adding metal is difficult or practically impossible with rapid injection moulding. In printing a change is a new file: our published preparation rate is €5 per file, minimum €10 per order. Every revision you still expect counts against moulding.

Lead time to the first part. Protolabs Network gives 6 to 10 weeks as typical: 4 to 6 for the mould plus 2 to 4 for production and shipping. Formlabs' aluminium-mould example takes 3 to 4 weeks, and Protolabs advertises lead times as fast as 7 days. We publish no fixed lead time: the date is in your quote, and larger runs can be delivered in parts.

Design rules, surface and material. Protolabs Network recommends a draft angle of at least 2°, a uniform wall thickness (1.2 to 3 mm is safe for most materials) and as few undercuts as possible. Reworking a printed design to those rules is a cost outside the formula. A moulded surface copies the mould and can be polished or textured; an FDM print shows its layer lines. We print PLA and PETG. FlinQ names PE, PP and ABS at €1.50 to €4 per kilo.

A short decision list

Stay with printing when:

  • the total quantity over the product's life stays below the break-even for your own quote

  • the design is still changing

  • you need several variants or personalised pieces

  • you need parts sooner than a mould can be made

Get a moulding quote when:

  • one geometry is final and you expect more than about 500 pieces, the lower bound at Protolabs Network and QDP

  • you will reorder the same part for years: once the mould exists you pay only the piece price (FlinQ)

  • the part needs a plastic or a surface that printing does not give

  • your own numbers put the quantity well past the break-even

To see where your own part stands, read how a run works on our small-batch 3D printing page or enter your weight, print time and quantity on the 3D printing cost page. Above a few hundred pieces we tell you honestly whether injection moulding becomes cheaper.