How to measure a hose or pipe for a 3D-printed adapter
By Sina Esfahani, OmniTechs · Published 22 November 2026
An adapter grips one surface on each side: it slides over the outside of a port or pipe, or it pushes into the inside of a hose or socket. Measure that surface with calipers in several directions, then add the taper, the wall thickness and the depth over which the parts overlap. The size printed on a hose is a name, not a measurement, so check your numbers with a short printed ring before the full adapter is made.
What the printed size tells you
Nominal sizes follow different conventions.
Garden hose: hose maker Flexzilla explains that the 1/2, 5/8 or 3/4 inch on a garden hose is its inside diameter. Gardena lists hoses of 13 mm (1/2 inch) and 19 mm (3/4 inch).
Vacuum and dust extraction: Kärcher sells suction hoses in nominal width DN 35 and labels that figure ID 35. Festool's D 27/32 hose is conical, from 27 mm to 32 mm, for machines with a D 27 connection. Accessory maker POWERTEC notes that dust hoses are named by inside diameter and that most fittings are tapered.
Rigid drain pipe: Wavin lists its 40 x 3 PVC pipe with an outside diameter of 40 mm and a wall of 3 mm. The bore is therefore 34 mm, 6 mm less than the name.
The same number can mean a bore, an outside or a connection system, and none describes the cuff or port in front of you.
The tools you need
Digital calipers with outside jaws, inside jaws and a depth rod. Mitutoyo states a resolution of 0.01 mm and a maximum permissible error of 0.02 mm for its 150 mm digital models, so the last digit is not the accuracy. On a soft hose, how hard you squeeze matters more.
A marker or tape to mark where you measured.
A phone for photos and the measurement sheet below.
Measure in this order
Decide what the adapter grips. For each side, note whether it goes over the outside or into the inside.
Check zero. Wipe the jaws, close them and check that the display reads zero.
Measure the outside diameter. Place the outside jaws at the mouth and measure in three directions around the circle. Use light, even force: calipers have no device that limits it. Write down all three values.
Measure the inside diameter. Insert the inside jaws as deeply as they go and take the largest reading, as Mitutoyo advises. Repeat in three directions.
Measure the taper. Mark a second position further along and measure the diameter there too. The taper is the difference between the two diameters divided by the distance between them. Send those three numbers rather than an angle.
Record out-of-round. A coiled or clamped hose is often oval. Note the largest and smallest reading at one position, without pressing the hose round. If the hose sat on a rigid port before, measure that port too.
Measure the wall. Put the outside jaws over the wall at the end. The outside diameter minus twice the wall should come close to the inside diameter; if not, measure again.
Measure the insertion depth. Use the depth rod, or a ruler along the port, up to the first shoulder, rib or latch, and note anything the adapter must clear or lock onto.
Note the surroundings. Record how large the adapter may be, what flows through it and whether the joint must come apart.
What to measure
| Measurement | How | Why it matters |
|---|---|---|
| Gripped surface | Note per side: over the outside or into the inside | Decides which diameter counts |
| Outside diameter | Outside jaws at the mouth, three directions | Size for an adapter that slides over |
| Inside diameter | Inside jaws as deep as they go, largest reading | Size for an adapter that pushes in |
| Second diameter and distance | Same measurement at a marked position further along | Gives the taper |
| Out-of-round | Largest and smallest reading at one position | Shows how oval a soft hose is |
| Wall thickness | Outside jaws over the wall at the end | Cross-check of inner and outer diameter |
| Insertion depth | Depth rod or ruler to the first shoulder | Sets the overlap length |
| Obstacles | Position and size of ribs, lugs and latches | The adapter must clear or use them |
Measurement sheet
| Item | Your value | Note |
|---|---|---|
| Side A: what it is | ... | Brand, model, hose or port |
| Side A: adapter grips | outside / inside | Choose one |
| Side A: diameter at the mouth | ... / ... / ... mm | Three directions |
| Side A: second diameter | ... mm at ... mm from the mouth | For the taper |
| Side A: wall thickness | ... mm | Measured at the end |
| Side A: insertion depth | ... mm | To the first shoulder or latch |
| Side B: what it is | ... | Brand, model, hose or port |
| Side B: adapter grips | outside / inside | Choose one |
| Side B: diameter at the mouth | ... / ... / ... mm | Three directions |
| Side B: second diameter | ... mm at ... mm from the mouth | For the taper |
| Side B: wall thickness | ... mm | Measured at the end |
| Side B: insertion depth | ... mm | To the first shoulder or latch |
| Largest adapter size | ... mm diameter, ... mm long | Space around the joint |
| What flows through | ... | Air, dust, cold or warm water, temperature |
| Must come apart | yes / no | And how often |
Common mistakes
Ordering by the printed size. It is a name, not the cuff or port you hold.
Measuring once. One direction hides an oval hose or a worn port.
Squeezing a soft hose. The jaws press it smaller.
Measuring a tapered port only at the mouth. Without a second diameter the adapter grips on one edge.
Copying a clearance from another project. There is no universal clearance; the fit comes from your counterpart and a test.
What to send with a request
Send the filled-in sheet, photos of both ends taken straight on with calipers or a ruler in view, and the brand and model of tool and hose. Say what flows through at what temperature, whether the joint must clamp, lock or come apart, and how many you need. An adapter for a pressurised water line, hot air or drinking water is assessed separately first.
Test with a short ring first
Ask for a short ring that carries only the gripping diameter and its taper. Check four things by hand: it goes on without force, seats to the depth you marked, stays put when the hose moves as in use, and comes off again. A loose or tight ring shows which way the diameter must change. Have it printed in the material of the final adapter.
OmniTechs redraws and prints adapters in PLA or PETG in Groningen; the first assessment is free via the 3D-printed parts page. The tolerances and clearance guide explains why a fit is tested rather than assumed, and measuring a replacement plastic part covers parts that are not round.

