How to measure a shaft for a replacement knob

By Sina Esfahani, OmniTechs · Published 22 November 2026

A replacement knob has to match four things: the shaft type (round, D-shaped, splined or square), its diameter, the flat or tooth pattern, and the space between panel and knob. Measure the shaft itself with calipers, not the bore of the broken knob, and note where the flat points in the off position. Have a small test ring printed before the whole knob.

Tell the shaft types apart

Switch the appliance off, unplug it and let it cool. On a gas appliance, close the gas supply first and follow the manufacturer's instructions before you touch a control: turning a bare gas valve can release gas even with the power off. Then pull the old knob off, or loosen its set screw first, and look at the shaft tip.

  • Round: a smooth cylinder, sometimes with a screwdriver slot; the knob holds with a set screw or collet.

  • D-shaped (flatted): round with one flat face, which stops the knob slipping and fixes the pointer.

  • Splined (knurled): fine teeth along the shaft, often split by a slot for a push-on knob.

  • Square: four flat sides.

Published sizes show why guessing fails

  • Bourns draws its PDB18 potentiometer with a 6.0 mm shaft, plain, flatted or knurled with 18 teeth. The flatted version is 4.5 mm across the flat.

  • Bourns' 90 series panel controls come with 1/4 inch (6.35 mm), 6 mm and 4 mm shafts.

  • Bourns' PDB183 guitar potentiometer has a split knurled shaft with 18 or 24 teeth.

  • Knob maker OKW names 3, 4, 6 and 8 mm and 1/4 inch as common spindle diameters, and a D profile of 6/4.6 mm.

A 6 mm and a 1/4 inch shaft differ by 0.35 mm, and Bourns and OKW put the flat of a 6 mm shaft 0.1 mm apart. These figures describe electronic controls. On a cooker or other appliance, every dimension is unknown until you measure it.

The tools you need

  • Digital calipers. Mitutoyo states a resolution of 0.01 mm and a maximum permissible error of 0.02 mm for its 150 mm digital models.

  • A marker and good light for counting teeth.

  • A phone for photos.

Measure in this order

  1. Diameter. Close the outside jaws on the round part in three directions, never across the flat or the slot. Use light, even force and do not squeeze a split shaft together.

  2. Flat. Put one jaw on the flat and one on the round back for the size across the flat. Then measure how far the flat runs from the tip.

  3. Teeth. Mark one tooth and count around twice. Measure over the tips, and the slot width on a split shaft.

  4. Square. Measure across the flats in both directions and across the corners.

  5. Length. Stand a steel ruler upright on the panel beside the shaft and read how far the tip stands above the panel; the panel face is your reference. Also measure how far a nut or bushing stands above the panel.

  6. Push travel. If the shaft is pushed in before it turns, measure panel to tip both released and pushed. The knob must not touch the panel before the travel ends.

  7. Pointer position. Do not turn the control of a gas appliance or of anything that is still connected. With the control in its off position, note, seen from the front, the clock position the flat faces and the one where the pointer must be. On a disconnected electronic control such as a potentiometer you can turn the shaft to its counter-clockwise stop, the position at which Bourns' datasheets draw the flat, and note it there.

  8. Space on the panel. Measure the distance to neighbouring knobs and markings.

  9. Old knob. Measure its bore only as a cross-check: Mitutoyo notes that caliper inside jaws read a small hole slightly too small.

What to measure

Nine measurements for a replacement knob, how to take each one on the shaft and what it decides in the design.
MeasurementHowWhy it matters
Shaft typeLook at the tip: smooth, one flat, teeth or squareDecides the shape of the bore
Shaft diameterOutside jaws on the round part, three directionsMain size of the bore
Across the flatOne jaw on the flat, one on the round backStops the knob slipping
Flat lengthFrom the tip along the shaftHow deep the D shape must run
Teeth and tip diameterMark one tooth, count twice, jaws over the tipsThe splines must mesh
Shaft lengthRuler upright on the panel beside the shaft, and nut heightBore depth and knob height
Push travelPanel to tip, released and pushedThe knob must not hit the panel
Flat direction in the off positionWithout turning the control, note the clock position; a stop only on a disconnected electronic controlPuts the pointer in the right place
Space on the panelDistance to neighbouring knobs and markingsLimits the knob diameter

Measurement sheet

Copy this sheet, fill in the lines that apply to your shaft type and send it with your photos.
ItemYour valueNote
Appliance...Brand, model and which control
Shaft typeround / D / splined / squareChoose one
Diameter... / ... / ... mmThree directions, round part only
Across the flat... mmD shaft only
Flat length... mmFrom the tip
Teeth... teeth, ... mm over the tipsSplined only; split yes / no
Across the flats... x ... mmSquare only
Height panel to tip... mmMeasured from the panel face
Nut or bushing height... mmAbove the panel
Push travel... mmOnly if the shaft is pushed in
Flat faces in the off position... o'clockDo not turn an appliance control to find a stop
Pointer in the off position... o'clockWhere the mark must point
Largest knob diameter... mmSpace between neighbours
Heat nearbyyes / no, about ... °COven, hob or heater

Knobs near heat

A knob on a cooker, oven or heater needs a material check before anything is printed. Filament maker Prusa writes that PLA softens and deforms above 60 °C and describes PETG as suited to use below 80 °C. Those are general statements about a material, not a rating for your knob: see PLA or PETG for your part. OmniTechs prints in PLA and PETG, assesses parts exposed to high temperature or with a safety function separately, and declines them when printing is not responsible. Say how warm the knob gets, and expect that some cooker knobs cannot be printed.

Common mistakes

  • Measuring the broken knob instead of the shaft.

  • Measuring the diameter across the flat.

  • Forgetting the nut and the push travel.

  • Leaving out the flat direction, so the pointer ends up turned.

  • Copying a clearance from another project. There is no universal clearance; the fit comes from your shaft and a test.

What to send with a request

Send the filled-in sheet, a photo straight onto the shaft tip and one from the side with calipers in view, and a photo of the panel. Add the brand and model, how the old knob was held (pushed on, set screw or clip), how many knobs you need and the pieces of the old knob if you have them.

Test with a ring first

Ask for a small ring that carries the bore shape. On a D-shaped, splined or square shaft, check by hand that it slides on, does not wobble, does not turn on the shaft and comes off again. On a smooth round shaft the ring only shows the diameter: the grip comes from the set screw or collet, so ask for the test ring with that fastening and check that it holds when tightened. A mark on the ring shows whether the pointer direction is right. Have it printed in the material of the final knob.

OmniTechs redraws and prints knobs in Groningen; the first assessment is free via the 3D-printed parts page. The tolerances and clearance guide explains why a fit is tested rather than assumed, and measuring a replacement plastic part covers other broken parts.