PLA, PETG, ASA and TPU side by side: what the manufacturers' datasheets say
By Sina Esfahani, OmniTechs · Published 22 November 2026
On the 17 manufacturer datasheets read for this page, the heat deflection temperature at 0.45 MPa runs from 55 to 60 °C for PLA, 68 to 78 °C for PETG and 93 to 103 °C for ASA. Flat-printed tensile strength is 35 to 64 MPa for PLA, 46 to 51 MPa for PETG and 37 to 45 MPa for ASA. These ranges take the yield value where a sheet reports yield (Prusament and UltiMaker) and the stated tensile strength otherwise, so they mix two measures; UltiMaker's flat stress at break is lower, 45.5 MPa for PLA and 38.5 MPa for PETG, and is shown in the table. Where a sheet also reports a specimen printed upright, that specimen reaches 27% to 89% of the flat strength, with a median of 75%.
Every figure below is the maker's own number for its test specimens under the stated standard. It is not a rating for a printed part and not a promise from OmniTechs. The sheets were read on 22 November 2026; their versions are in the source list.
Mechanical and thermal figures per datasheet
One row is one datasheet for one standard grade. Values are copied as printed, without the ± spread that some sheets give; Prusament's moduli are converted from GPa to MPa. "Flat" is the specimen printed lying on the bed, which the sheets call horizontal, X-Y or XY. "Not stated" means the sheet gives no value or prints N/A.
PLA, PETG, ASA and TPU: figures from 17 manufacturer datasheets
| Datasheet | Density (g/cm³) | Tensile strength, flat (MPa) | Tensile modulus, flat (MPa) | Elongation at break, flat (%) | HDT at 0.45 / 1.8 MPa; Vicat (°C) |
|---|---|---|---|---|---|
| Prusament PLA | 1.24 | 51 (yield) | 2,300 | not stated (2.9 at yield) | 55 / 55; Vicat not stated |
| Polymaker PolyLite PLA | 1.17 | 52.3 | 3,426.9 | 6.3 | 60 / 58; Vicat 63 |
| Bambu Lab PLA Basic | 1.24 | 35 | 2,580 | 12.2 | 57 / 54; Vicat 57 |
| UltiMaker PLA | 1.24 | 52.5 (yield); 45.5 (break) | 3,250 | 7.8 | 58.8 / not stated; Vicat 64.5 |
| colorFabb PLA/PHA | 1.2 | 64 | 3,070 | 4 | not stated |
| Prusament PETG | 1.27 | 47 (yield) | 1,500 | not stated (5.1 at yield) | 68 / 68; Vicat not stated |
| Polymaker PolyLite PETG | 1.25 | 50.8 | 2,116.8 | 8.4 | 78 / 75; Vicat 84 |
| Bambu Lab PETG Basic | 1.25 | 51 | 2,780 | 9.5 | 71 / 68; Vicat 69 |
| UltiMaker PETG | 1.27 | 46.2 (yield); 38.5 (break) | 1,939 | 7.6 | 76.2 / not stated; Vicat 82.9 |
| colorFabb PETG Economy | 1.28 | 50 | 1,900 | 90 | HDT-B 65; Vicat not stated |
| Prusament ASA | 1.07 | 42 (yield) | 1,600 | not stated (3.4 at yield) | 93 / 86; Vicat not stated |
| Polymaker ASA | 1.13 | 43.8 | 2,379 | 6.7 | 103 / 100; Vicat 105 |
| Bambu Lab ASA | 1.05 | 37 | 2,450 | 9.2 | 100 / 92; Vicat 106 |
| colorFabb ASA | 1.07 | 45 | 2,100 | 6.5 | HDT-B 87; Vicat not stated |
| Polymaker PolyFlex TPU95 | 1.20 to 1.24 | not stated | 33.6 | 551.2 | not stated |
| Bambu Lab TPU 95A HF | 1.22 | 27.3 | 9.8 | more than 650 | not stated |
| UltiMaker TPU 95A | 1.22 | 23.7 (break) | 67 | more than 560 | 50.3 / not stated; Vicat 115.7 |
Read these points with the table:
Yield or break. Prusament reports tensile strength and elongation at the yield point only. UltiMaker reports both yield and break. The other three makers print one tensile strength figure.
Heat column. UltiMaker's load is 0.455 MPa and it gives no value at 1.8 MPa. colorFabb labels its single value "HDT-B" without a load, so it is outside the ranges in the opening paragraph. Vicat is a separate softening test, listed next to HDT and not in place of it.
colorFabb. The sheet says its density and thermal values come from the raw-material supplier, not from colorFabb's printed specimens.
TPU. Polymaker tests PolyFlex TPU95 to ISO 37 and prints the stress at fixed strains (25.8 MPa at 400%) instead of a tensile strength. The three modulus figures, 9.8, 33.6 and 67 MPa, come from three different test methods.
Recommended nozzle and bed temperatures
These are the print settings each maker recommends for its own filament. UltiMaker's three technical data sheets list no print temperatures.
Recommended nozzle and bed temperatures per datasheet
| Datasheet | Nozzle (°C) | Bed (°C) | Chamber or enclosure |
|---|---|---|---|
| Prusament PLA | 210 ± 10 | 40 to 60 | not stated |
| Polymaker PolyLite PLA | 190 to 230 | 25 to 60 | closed chamber not needed |
| Bambu Lab PLA Basic | 190 to 230 | 35 to 45 | chamber 25 to 45 °C |
| UltiMaker PLA | not stated | not stated | not stated |
| colorFabb PLA/PHA | 195 to 220 | 50 to 60 | not stated |
| Prusament PETG | 250 ± 10 | 80 ± 10 | not stated |
| Polymaker PolyLite PETG | 230 to 260 | 70 to 80 | closed chamber not needed |
| Bambu Lab PETG Basic | 230 to 260 | 65 to 75 | chamber 35 to 50 °C |
| UltiMaker PETG | not stated | not stated | not stated |
| colorFabb PETG Economy | 235 to 255 | 70 to 80 | not stated |
| Prusament ASA | 260 ± 10 | 110 ± 5 | not stated |
| Polymaker ASA | 230 to 260 | 75 to 95 | closed chamber needed |
| Bambu Lab ASA | 240 to 270 | 80 to 100 | chamber 45 to 60 °C |
| colorFabb ASA | 240 to 260 | 90 to 100 | not stated |
| Polymaker PolyFlex TPU95 | 210 to 230 | 25 to 60 | closed chamber not needed |
| Bambu Lab TPU 95A HF | 220 to 240 | 30 to 35 | chamber 25 to 45 °C |
| UltiMaker TPU 95A | not stated | not stated | not stated |
How the makers tested, and why rows are not comparable
All 17 sheets test 3D-printed specimens, but each maker prints and pulls them differently.
How five filament makers test their datasheet specimens
| Maker | Tensile standard | Printed specimens | Directions reported | Strength reported as | Heat test |
|---|---|---|---|---|---|
| Prusa Polymers (Prusament) | ISO 527-1 | 0.20 mm layers, 2 perimeters, 100% infill | Horizontal and on edge ("vertical xz") | Yield | HDT, ISO 75, 0.45 and 1.80 MPa |
| Polymaker | ISO 527 / GB/T 1040; TPU: ISO 37 | 2 shells, 100% infill; layer height not stated | X-Y and Z; TPU: X-Y only | Tensile strength; TPU: stress at fixed strain | HDT, ISO 75, 0.45 and 1.8 MPa; Vicat, ISO 306 |
| Bambu Lab | ISO 527 / GB/T 1040 | 100% infill; PLA, ASA and TPU specimens annealed and dried first | X-Y and Z | Tensile strength | HDT, ISO 75, 0.45 and 1.8 MPa; Vicat, ISO 306 |
| UltiMaker | ASTM D3039 | 0.15 mm layers, 100% infill, 215 × 20 × 4 mm | XY flat, YZ side, Z up | Yield and break | HDT, ISO 75-2/B, 0.455 MPa; Vicat, ISO 306/A120 |
| colorFabb | ISO 527-1A | XY plane, 0.15 mm layers, 100% infill | XY only | Tensile strength | HDT-B, ISO 75, from the raw-material supplier |
Four differences matter when you compare rows:
Printed is not injection-moulded. colorFabb prints both sets on one sheet. Its ASA drops from 50 to 45 MPa tensile strength and from 20% to 6.5% elongation at break when the specimen is printed instead of moulded. Its PLA/PHA drops from 11% to 4% elongation. Its PETG Economy keeps 50 MPa, loses flexural modulus (1,800 to 1,000 MPa) and gains elongation (35% to 90%). A value from a raw-material sheet is not a value for a print, and the direction of the difference is not fixed.
The standards differ. Four makers cite ISO 527; UltiMaker pulls a 215 × 20 × 4 mm specimen to ASTM D3039.
The conditioning differs. Bambu Lab annealed and dried its specimens before testing: PLA Basic at 55 °C for 8 hours, ASA at 80 °C for 12 hours and TPU 95A HF at 70 °C for 12 hours. Its PETG Basic sheet does not say the specimens were annealed. UltiMaker kept specimens at room temperature for at least 24 hours.
The direction differs. Prusament's second direction is a specimen on its edge, not upright; colorFabb tests one direction.
Flat against upright specimens
Ten sheets report tensile strength for a specimen printed upright, where the load pulls the layers apart. UltiMaker's rows use stress at break, because its upright specimens show no yield value.
Tensile strength of flat and upright printed specimens on ten datasheets
| Datasheet | Flat (MPa) | Upright, Z (MPa) | Upright as share of flat |
|---|---|---|---|
| Polymaker PolyLite PLA | 52.3 | 40.5 | 77% |
| Bambu Lab PLA Basic | 35 | 31 | 89% |
| UltiMaker PLA (break) | 45.5 | 33.1 | 73% |
| Polymaker PolyLite PETG | 50.8 | 42.8 | 84% |
| Bambu Lab PETG Basic | 51 | 35 | 69% |
| UltiMaker PETG (break) | 38.5 | 19.0 | 49% |
| Polymaker ASA | 43.8 | 32 | 73% |
| Bambu Lab ASA | 37 | 31 | 84% |
| Bambu Lab TPU 95A HF | 27.3 | 22.3 | 82% |
| UltiMaker TPU 95A (break) | 23.7 | 6.4 | 27% |
The eight PLA, PETG and ASA rows run from 49% to 89%. UltiMaker's sheets state that the interlayer direction typically has the lowest strength in filament printing. Prusament lists a separate interlayer adhesion value by its own method: 17 MPa for PLA, 18 MPa for PETG and 11 MPa for ASA.
How to use these tables
Start from the requirement. Decide whether heat, stiffness, impact or flexibility is the question. One high number does not answer all four.
Compare within one maker first. Rows from one maker share a method. At 0.45 MPa the heat deflection temperature rises from PLA to PETG to ASA at Polymaker (60, 78, 103 °C), Prusament (55, 68, 93 °C) and Bambu Lab (57, 71, 100 °C). Between makers, a difference of a few units can be the test and not the plastic.
Ask which grade will be used. A material name is a family. Request the sheet for the exact filament and check its version, standard and direction.
Treat every figure as a specimen value. A printed part behaves according to its shape, wall thickness, orientation and settings. Where failure matters, test the real part in the real direction of load.
What OmniTechs prints
According to its public pages, OmniTechs prints PLA and PETG as standard materials on its own FDM printers in Groningen. ASA is not a standard material there: it is printed on request on an enclosed printer after a feasibility check. TPU is printed after a feasibility check, and the quote states the hardness of the filament used, with its datasheet. Those pages name no filament brand and confirm the exact grade in the quote, so none of the 17 sheets above should be read as OmniTechs stock.
To pick a material for a part, start with the material chooser and the comparison of PLA or PETG for your part. To read a single sheet properly, use the guide to reading a PETG material datasheet. For what walls, infill and orientation do to a real part, see how strong 3D-printed parts are.
Sources
Prusa Polymers: Prusament PETG technical datasheet, version 1.1 of 16 February 2022
Prusa Polymers: Prusament ASA technical datasheet, version 1.1 of 20 May 2024
UltiMaker: TPU 95A technical data sheet v2.01 of 15 September 2025
colorFabb: PLA/PHA technical datasheet v1.0 of 13 September 2023
colorFabb: PETG Economy technical datasheet v1.0 of 20 November 2023

