Selling 3D-printed products in the EU: which product safety rules apply

By Sina Esfahani, OmniTechs · Published 22 November 2026

A 3D-printed product sold to consumers in the EU falls under the General Product Safety Regulation (EU) 2023/988 (GPSR), which has applied since 13 December 2024, unless a specific EU product law covers the same risks. A print designed or intended for play by children under 14 is a toy under Directive 2009/48/EC and must carry CE marking. If the product is sold under your name or trademark, the regulation treats you as its manufacturer, whoever printed it.

This page is a reading guide to the published rules as read on 22 November 2026, not legal advice; the official text and the market surveillance authority decide.

The rules at a glance

EU product safety rules for sellers of 3D-printed products

Which rule applies when and what it asks, read from the Official Journal texts and European Commission pages on 22 November 2026.
RuleApplies whenWhat it asks of the maker or sellerOfficial source
General Product Safety Regulation (EU) 2023/988Consumer products since 13 December 2024; under EU harmonisation legislation only for risks that law does not coverSell only safe products; without harmonisation legislation also a risk analysis and technical documentation, kept 10 yearsRegulation (EU) 2023/988, Articles 2, 5, 9 and 52
GPSR: identification and contact detailsProducts not under EU harmonisation legislation, placed on the market from 13 December 2024Batch or type number, manufacturer name, postal and electronic address on the productRegulation (EU) 2023/988, Articles 9(5) and 9(6)
GPSR: online offersAny product offered online to EU consumers, including toys and electrical productsListing shows manufacturer name and addresses, a picture, the type, any other product identifier and the warningsRegulation (EU) 2023/988, Article 19; Commission notice C/2025/6233, section 2.2
Toy Safety Directive 2009/48/ECProducts designed or intended, whether or not exclusively, for play by children under 14Safety requirements, conformity assessment, technical documentation, CE marking, name and address on the toy, warningsDirective 2009/48/EC, Articles 2, 4, 10, 11 and 16
Toy rule for small partsToys clearly intended for children under 36 monthsToy and detachable parts sized so they cannot be swallowed or inhaledDirective 2009/48/EC, Annex II, part I, point 4(d)
CE markingOnly where an EU product law requires it, such as for toys and electrical equipmentAffix after the conformity assessment; forbidden on other productsEuropean Commission and Your Europe CE marking pages
Low Voltage Directive 2014/35/EUElectrical equipment at 50 to 1000 V AC or 75 to 1500 V DCManufacturer carries out the conformity assessment; no notified body requiredEuropean Commission, Low Voltage Directive page
EMC Directive 2014/30/EUElectrical and electronic equipment placed on the marketMeet the EMC requirements for emissions and immunityEuropean Commission, EMC Directive page
Toy Safety Regulation (EU) 2025/2509Toys from 1 August 2030, when the directive is repealedNew rules, including a digital product passportRegulation (EU) 2025/2509, Articles 56 and 59

Which rule to check first, by product

The examples do not classify your product; the design, the listing and the intended buyer all count.

Printed product examples and the rule to check first

Five product examples and the rule the official sources point to first, read from the regulation, the directive and Commission and NVWA pages on 22 November 2026.
Product exampleRule to check first, according to the sourcesNote
Decorative vaseGeneral Product Safety RegulationNo CE marking unless another product law applies; also assess looks that attract children or resemble food
KeychainToy scope test, then the General Product Safety RegulationA figure made for play can make it a toy; children's fashion accessories not for use in play are not toys
Fidget or articulated figureToy Safety Directive scope testIf designed or intended for play by under-14s, also in part, it is a toy and needs CE marking
Lamp with electronicsLow Voltage Directive and EMC DirectiveDepends on the voltage; radio modules bring in the Radio Equipment Directive; child-appealing luminaires are not toys
Children's toyToy Safety DirectiveCE marking, warnings and the rule for under 36 months; the online-offer rule of the GPSR also applies

Who is the manufacturer of a 3D print?

The GPSR defines the manufacturer as "any natural or legal person who manufactures a product or has a product designed or manufactured, and markets that product under that person's name or trademark". The Toy Safety Directive uses the same definition for toys.

Read against that definition:

  • You print someone else's design and sell it under your shop name. You manufacture the product and market it under your name.

  • A print service makes it and it is sold under your brand. You have the product manufactured and market it under your name. The Commission's guidelines say businesses are manufacturers when they market the product under their name, "even if they did not produce the product themselves".

The guidelines call the obligations "relevant for all sizes of business" and say purely consumer-to-consumer transactions fall outside the regulation.

What must be on the product or its packaging

The product laws that provide for CE marking, such as those for toys and electrical equipment, are EU harmonisation legislation. For products under them, Articles 9 to 18 of the GPSR do not apply; that legislation sets the marking and documentation instead.

For a product without harmonisation legislation, for example a decorative vase under the GPSR alone, Articles 9 and 16 of the GPSR ask the manufacturer for:

  • An identifier. A type, batch or serial number or another element that identifies the product, easily visible and legible.

  • Name and contact details. Name, registered trade name or trade mark, postal address and electronic address, on the product.

  • Instructions and safety information in a language consumers easily understand. They are not required where the product can be used safely without them.

  • The responsible person in the EU. According to the guidelines, a manufacturer established in the EU is itself that person.

Where the size or nature of the product does not allow it, the identifier and contact details go on the packaging or in an accompanying document. The guidelines add that in principle only size justifies that move, not looks. Such a product also needs an internal risk analysis and technical documentation before sale; the guidelines say the detail should be proportionate to its complexity and risks.

For a toy, Article 4 of the Toy Safety Directive asks instead for a type, batch, serial or model number, the manufacturer's name and address, instructions and safety information, technical documentation and the CE marking. For electrical equipment, the Commission's pages name a conformity assessment by the manufacturer and CE marking; the marking rules in the two directives were not read for this page.

What the online offer must show

Article 19 of the GPSR applies to every online offer, toys and electrical products included. The listing must clearly and visibly show:

  • the manufacturer's name, registered trade name or trade mark, with the postal and electronic address;

  • where the manufacturer is not established in the EU, the name and the postal and electronic address of the responsible person;

  • information that identifies the product: a picture of it, its type and any other product identifier;

  • any warning or safety information that has to be on the product, on its packaging or in an accompanying document, in a language consumers easily understand.

Toys, CE marking and lamps

Annex I of the Toy Safety Directive lists what is not a toy, including decorative objects for festivities and collectors' products that visibly state they are for collectors of 14 and above; its examples include detailed and faithful scale models and decorative dolls. A toy clearly intended for children under 36 months, and its detachable parts, must be sized so that they cannot be swallowed or inhaled. The warning "Not suitable for children under 36 months" may not be used where it conflicts with the toy's intended use.

CE marking is not a general safety label. The Commission states that it is compulsory only for most products covered by the New Approach directives and that it is forbidden on other products. A vase or keychain under the GPSR alone therefore carries no CE marking.

For lamps, the Commission's page puts electrical equipment between 50 and 1000 V AC or 75 and 1500 V DC under the Low Voltage Directive. Below those limits it refers to general product safety law. Your Europe adds that the manufacturer answers for the entire product, including components supplied by others, so check the Low Voltage and EMC directives for the complete lamp.

How this page was put together and where it stops

Each cell was read on 22 November 2026 from the Official Journal text, a European Commission page or the Dutch NVWA; the Commission's guidelines have no legal force. The page leaves out chemical limits for toys, food-contact products, the full text of the two electrical directives and penalties.

In the Netherlands the NVWA supervises consumer products and offers a free self-inspection. Start from the product row that fits, read the cited article, and ask the authority when the scope is unclear.

What OmniTechs says about its own role

OmniTechs' terms cover its website and direct orders of keychains, lamps and vases. For white-label production, its dropshipping page says the seller handles the model, the commercial rights and the complete configuration; OmniTechs prints, finishes, inspects, packs and ships, and the customer sees the seller's brand. A complete lamp is accepted only after the necessary suitability and product qualification have been demonstrated. The pages name no role under the GPSR; the definition above turns on whose name the product carries.

Costs and margins are in the guide to selling 3D prints, model rights in the licence reference, and production under your brand on the 3D print dropshipping page.