How many metres are in a spool? Filament weight, length and volume for each material
By Sina Esfahani, OmniTechs · Published 22 November 2026
A 1 kg spool of 1.75 mm PLA holds about 335 m of filament, and one metre of it weighs just under 3 g. PETG is denser, so the same kilogram is about 327 m; ABS is lighter and runs to about 396 m. In 2.85 mm filament a kilogram of PLA is about 126 m.
All of these follow from one number per material, its density, and from the cross-section of the filament. This page lists the densities that filament makers publish in their own datasheets, converts them for 1.75 mm and 2.85 mm filament, and shows the formula so you can redo the sum for any other density.
The densities makers publish
Filament density as published by makers
| Material | Maker and product | Density, g/cm³ | Test method stated |
|---|---|---|---|
| PLA | Prusament PLA | 1.24 | ISO 1183 |
| PLA | Bambu Lab PLA Basic | 1.24 | ISO 1183 |
| PLA | eSUN PLA+ | 1.24 | Not stated |
| PLA | UltiMaker PLA | 1.24 | ASTM D1505 |
| PLA | Polymaker PolyLite PLA | 1.17 | ISO 1183, GB/T 1033 |
| PETG | Prusament PETG | 1.27 | ISO 1183 |
| PETG | eSUN PETG | 1.27 | Not stated |
| PETG | UltiMaker PETG | 1.27 | ISO 1183 |
| PETG | Bambu Lab PETG Basic | 1.25 | ISO 1183 |
| PETG | Polymaker PolyLite PETG | 1.25 | Not stated |
| PETG | Polymaker PETG | 1.3 | Not stated |
| ABS | Polymaker PolyLite ABS | 1.04 | Not stated |
| ABS | Bambu Lab ABS | 1.05 | ISO 1183 |
| ABS | eSUN ABS+ | 1.06 | Not stated |
| ABS | UltiMaker ABS | 1.1 | ISO 1183 |
| ASA | Bambu Lab ASA | 1.05 | ISO 1183 |
| ASA | Prusament ASA | 1.07 | ISO 1183 |
| ASA | Polymaker ASA | 1.13 | Not stated |
| TPU 95A | eSUN TPU-95A | 1.21 | Not stated |
| TPU 95A | Bambu Lab TPU 95A HF | 1.22 | ISO 1183 |
| TPU 95A | Polymaker PolyFlex TPU95 | 1.22 | Not stated |
| TPU 95A | UltiMaker TPU 95A | 1.22 | ASTM D782 as printed |
| TPU 95A | Prusament TPU 95A | 1.25 | ISO 1183 |
| PA (nylon) | Prusament PA11 | 1.02 | ISO 1183 |
| PA (nylon) | Polymaker PolyMide CoPA | 1.12 | Not stated |
| PA (nylon) | eSUN PA | 1.12 | Not stated |
| PA (nylon) | UltiMaker Nylon | 1.14 | ISO 1183 |
PLA is the most uniform: four of the five makers state 1.24. The spread grows where one name covers several plastics. Nylon is a family, and Prusament's PA11 at 1.02 is a different polymer from the nylons listed at 1.12 to 1.14. Colour and additives matter too. Polymaker lists its Panchroma Matte PLA at 1.37, which is about 303 m per kilogram of 1.75 mm filament, roughly 10% fewer metres than plain PLA.
These are the makers' figures for the filament material. They are not a rating for a printed part: a print with infill contains air, so it weighs less per cubic centimetre than the solid filament it was made from.
Metres per kilogram for 1.75 mm filament
1.75 mm filament: metres per kilogram, grams per metre and volume
| Material | Density used | Metres per kg | Range across makers | Grams per metre | cm³ per kg |
|---|---|---|---|---|---|
| PLA | 1.24 | 335.3 | 335.3 to 355.3 | 2.98 | 806 |
| PETG | 1.27 | 327.4 | 319.8 to 332.6 | 3.05 | 787 |
| ABS | 1.05 | 396.0 | 378.0 to 399.8 | 2.53 | 952 |
| ASA | 1.07 | 388.6 | 367.9 to 396.0 | 2.57 | 935 |
| TPU 95A | 1.22 | 340.8 | 332.6 to 343.6 | 2.93 | 820 |
| PA (nylon) | 1.12 | 371.2 | 364.7 to 407.6 | 2.69 | 893 |
The density used is the figure most makers share, or the middle one where they all differ: 1.05 for ABS is Bambu Lab's figure and 1.07 for ASA is Prusament's. For a 750 g or 250 g spool, multiply the metres by 0.75 or 0.25.
Metres per kilogram for 2.85 mm filament
2.85 mm filament: metres per kilogram, grams per metre and volume
| Material | Density used | Metres per kg | Range across makers | Grams per metre | cm³ per kg |
|---|---|---|---|---|---|
| PLA | 1.24 | 126.4 | 126.4 to 134.0 | 7.91 | 806 |
| PETG | 1.27 | 123.4 | 120.6 to 125.4 | 8.10 | 787 |
| ABS | 1.05 | 149.3 | 142.5 to 150.7 | 6.70 | 952 |
| ASA | 1.07 | 146.5 | 138.7 to 149.3 | 6.83 | 935 |
| TPU 95A | 1.22 | 128.5 | 125.4 to 129.5 | 7.78 | 820 |
| PA (nylon) | 1.12 | 140.0 | 137.5 to 153.7 | 7.14 | 893 |
A kilogram of thick filament is about 2.65 times shorter than a kilogram of thin filament, because the cross-section is 2.65 times larger. The volume per kilogram is the same for both.
The formula
Cross-section area in mm² = π × (diameter ÷ 2)². For 1.75 mm that is 2.405 mm², for 2.85 mm it is 6.379 mm².
Grams per metre = density in g/cm³ × area in mm². This works because one metre of filament with a cross-section of 1 mm² is exactly 1 cm³.
Metres per kilogram = 1,000 ÷ grams per metre.
Volume in cm³ per kilogram = 1,000 ÷ density.
For PLA: 1.24 × 2.405 = 2.98 g per metre, and 1,000 ÷ 2.98 gives 335 m per kilogram. The tables were calculated without rounding in between and then rounded to one decimal for metres and two for grams.
The formula can be checked against a maker. UltiMaker prints the filament length on its datasheets for 750 g spools of 2.85 mm: about 95 m for PLA, 107 m for ABS and 93 m for PETG. With UltiMaker's own densities the formula gives 94.8 m, 106.9 m and 92.6 m.
How exact is the length?
The length depends on the real diameter, and makers allow a band. Prusament's datasheets state 1.75 ± 0.02 mm for PLA and PETG, ± 0.04 mm for ASA and ± 0.06 mm for TPU 95A. UltiMaker's state 2.85 ± 0.10 mm for PLA and ABS and ± 0.05 mm for PETG and nylon. At the two edges of Prusament's PLA band, a kilogram is between 327.7 m and 343.1 m long.
The weight does not move with the diameter. A spool is sold by weight, so grams are the safer unit for planning, and metres are best treated as a close estimate.
What a 1 kg spool makes
What a 1 kg spool makes
| Product group | Median filament | Products per kg | Whole products | Same weight in 1.75 mm PLA |
|---|---|---|---|---|
| All 961 products | 100.8 g | 9.9 | 9 | 33.8 m |
| Decoration | 78.1 g | 12.8 | 12 | 26.2 m |
| Organisers | 111.5 g | 9.0 | 8 | 37.4 m |
| Vases | 161.2 g | 6.2 | 6 | 54.0 m |
| Lamps | 252.5 g | 4.0 | 3 | 84.7 m |
| Keychains | 13.7 g | 73.0 | 72 | 4.6 m |
| Accessories | 11.1 g | 90.1 | 90 | 3.7 m |
The weights are the medians from our article on how long a 3D print takes, which covers 961 catalogue products (OmniTechs catalogue data, 22 November 2026). A kilogram is nine complete products of median weight, with 93 g left over. This is plain division. It ignores failed prints and the purge when a printer changes colour, so a real spool yields fewer. Whether the recorded slicer weights already include support material was not checked for this page.
Using these figures
To see what is left on a spool, weigh the spool, subtract the weight of the empty spool (weigh an empty one of the same type) and divide the remaining grams by the grams per metre. 150 g of 1.75 mm PLA is 150 ÷ 2.98, about 50 m.
If your slicer reports metres, multiply by the grams per metre to get the weight, and compare that with what is left.
For material cost per metre, divide the price per kilogram by the metres per kilogram. At our published PLA rate of €40 per kg excluding VAT, a metre of 1.75 mm PLA is about 12 cents of material; at the PETG rate of €44 per kg it is about 13 cents.
For a filament that is not in the tables, take the density from its datasheet and use the formula.
Material is only part of a print's price. Our print time data shows how hours and grams relate, the 3D printing cost page has the current rates and a calculator, and the material guide helps you choose a plastic. PLA and PETG are our usual starting points; the other materials are listed here as reference figures, not as a standing offer.
Sources
Prusament PLA: technical datasheet, density and diameter.
Prusament PETG: technical datasheet.
Prusament ASA: technical datasheet.
Prusament TPU 95A: technical datasheet.
Prusament PA11: technical datasheet.
Polymaker technical data at a glance: density per product.
Bambu Lab PLA Basic: technical data sheet V3.0.
Bambu Lab PETG Basic: technical data sheet V3.0.
Bambu Lab ABS: technical data sheet V3.0.
Bambu Lab ASA: technical data sheet V3.0.
Bambu Lab TPU 95A HF: technical data sheet V1.0.

