What does the electricity for a 3D print cost? A calculation from published figures

By Sina Esfahani, OmniTechs · Published 22 November 2026

An hour of desktop FDM printing in PLA or PETG uses about 2 to 7 euro cents of electricity in the Netherlands. A print of 3 h 40 min, the median in our catalogue, comes to between 7 and 25 cents. This is a calculation from published figures, not a measurement: it combines the power figures that printer makers publish with the official consumer price per kWh, and OmniTechs has not metered its own printers for this article.

The spread comes from the printer. Of the twelve printers in the table below, seven are listed at 75 to 105 W while printing PLA or PETG and four at 150 to 250 W. The twelfth, the Prusa XL, is listed at 235 W without a stated material.

What printer makers publish

Power figures published by printer makers

Figures as published by Bambu Lab and Prusa Research on their own pages, read on 22 November 2026. Makers' figures, not measured by OmniTechs. Bambu Lab maximum power is at 220 V.
PrinterPrinting PLAPrinting PETGStandbyMaximum or heat-up
Bambu Lab A1 mini80 W75 W6.1 to 7.3 W150 W
Bambu Lab A195 WNot published4 to 5.4 W1,300 W
Bambu Lab P1S105 WNot published5.2 to 6 W1,000 W
Bambu Lab X1C105 WNot published8.5 to 9.9 W1,000 W
Bambu Lab P2S200 WNot published7.3 to 8.2 W1,200 W
Bambu Lab H2S200 W180 W26 to 26.5 W1,800 W
Bambu Lab H2D197 W150 W24.8 to 27 W1,800 W
Bambu Lab X2D250 WNot published7.3 to 8.2 W1,600 W
Prusa MK4S80 WNot publishedNot publishedNot published
Prusa CORE One+90 WNot publishedNot publishedNot published
Prusa CORE One L+About 90 WNot published16 WAbout 630 W preheating
Prusa XL, one tool head235 W, material not statedNot published80 W550 W heating up

What each figure refers to matters:

  • Bambu Lab's averages for the A1, P1 and X1 series come with a test duration of 15 to 18 minutes and the energy used in that time; the A1 mini PETG run lasted 23 minutes. The page does not describe the printed model. For the P2S and X2D it gives a steady-state printing power for PLA, for the X2D at 25 °C ambient.

  • Prusa lists "PLA settings: 80W" for the MK4S and 90 W for the CORE One+. Its support pages add that 80 W is an average measured on an MK-series printer at 26 °C room temperature with generic PLA.

  • The maximum is the highest draw the maker lists, not an average. Prusa labels its figures for the CORE One L+ and the XL as preheating and heating up.

For PLA and PETG the lowest published average is 75 W and the highest 250 W. The calculation below uses those two as its edges.

The price per kWh

Statistics Netherlands (CBS) publishes average consumer energy tariffs every month. For October 2026, the latest and still provisional month, the two parts of the bill that are charged per kWh add up to €0.271 including VAT: a variable delivery tariff of €0.1601 and energy tax of €0.11085. The other parts of a Dutch bill are fixed amounts per year, so one more print does not change them. Your own price depends on your contract.

For comparison, Eurostat reports an average household price for the first half of 2026 of €0.2832 per kWh in the EU and €0.2440 in the Netherlands, all taxes and levies included, for households using 2,500 to 4,999 kWh a year. That figure spreads the whole bill over the kWh used, fixed charges and the Dutch tax reduction included, which is why it differs from the CBS per-kWh price.

Electricity per print

The formula is hours × watts ÷ 1,000 × price per kWh. One hour at 75 W is 0.075 kWh, and 0.075 × €0.271 is 2 cents.

Calculated electricity use and cost per print

Calculated, not measured: makers' lowest and highest published average power for PLA or PETG, and 0.271 euro per kWh including VAT (CBS, October 2026, provisional). Print times: OmniTechs catalogue data, 22 November 2026.
PrintHourskWh at 75 WCost at 75 WkWh at 250 WCost at 250 W
One hour1.000.075€0.0200.250€0.068
25th percentile of our catalogue1.740.131€0.0350.435€0.118
Catalogue median3.660.275€0.0740.915€0.248
75th percentile7.100.533€0.1441.775€0.481
90th percentile11.970.898€0.2432.993€0.811

The print times are those of 961 catalogue products in our article on how long a 3D print takes (OmniTechs catalogue data, 22 November 2026). Nine in ten of those products stay under €0.25 of electricity at 75 W and under €0.82 at 250 W. At 105 W, the figure Bambu Lab gives for the P1S and X1C, the median print uses 0.384 kWh, about 10 cents.

With the EU average price the same hour costs €0.021 to €0.071, and the median print €0.078 to €0.259.

Compared with an hourly print rate

On our 3D printing cost page print time is €1.04 per hour excluding VAT in the first band. To compare like with like, take the electricity price without VAT as well: €0.224 per kWh. An hour then costs €0.017 at 75 W and €0.056 at 250 W, which is 1.6% to 5.4% of that hourly rate. For the median print, the time charge is €3.81 and the calculated electricity €0.061 to €0.205.

Two cautions belong with that percentage. The €1.04 is a selling rate for print time; what it is built from is not published, so the percentage only sets two published numbers side by side. And the electricity side is built from a consumer price and makers' figures, not from our own meter or contract. The comparison shows the order of size, nothing more: electricity is a small part of what an hour of printing is sold for.

What is not in the calculation

  • Heated enclosures and chambers, filament drying and heating the room are outside it. As an indication of size, Bambu Lab lists 80 W and 170 W for its AMS 2 Pro and AMS HT filament units while they dry filament.

  • Materials that print hotter draw more. Prusa lists 120 W for ABS against 80 W for PLA on the MK4S; Bambu Lab lists 200 W for ABS against 95 W for PLA on the A1.

  • Standby counts if a printer stays on. At 6 W, a full day is 0.144 kWh, about 4 cents.

  • Failed prints and test pieces use electricity too.

  • The makers' averages come from their own test runs, at 25 or 26 °C where a room temperature is stated. Other models, settings and rooms give other numbers.

Using these figures

  • For your own print, take the hours from your slicer, the average watts your printer's maker publishes and the kWh price on your contract, and apply the formula.

  • For a real number instead of a calculated one, a plug-in energy meter between the socket and the printer records the kWh of a complete print.

  • If you quote this page, call it a calculation from published figures and name the price date: October 2026, provisional.

Electricity is one of the smaller lines in the price of a print. Our print time data shows how long real products take, the cost page lists the current rates with a calculator, and why 3D printing quotes differ explains what else suppliers put in a price.