Nozzle size guide: layer height and line width for 0.2, 0.4, 0.6 and 0.8 mm nozzles

By Sina Esfahani, OmniTechs · Published 22 November 2026

Printer and slicer makers tie both settings to the nozzle diameter. Layer height tops out at 70% of the nozzle diameter according to Bambu Lab and at 80% according to Prusa and, on a printer with one nozzle size, the warning limit in UltiMaker Cura, and line width normally equals the nozzle diameter or sits slightly above it. For the common 0.4 mm nozzle that gives a layer height of 0.08 to 0.28 mm (Bambu Lab) or up to 0.32 mm (Prusa, Cura), and a line about 0.4 to 0.45 mm wide.

Layer height and line width per nozzle

Layer height and line width per nozzle size, by maker

Ranges published by Bambu Lab, Prusa, UltiMaker and E3D, read on 22 November 2026 and worked out per nozzle from each maker's rule. These are the makers' recommendations and slicer limits, not OmniTechs settings.
NozzleLayer heightLine widthSource and rule
0.2 mm0.04 to 0.14 mm0.15 to 0.30 mmBambu Lab: 20 to 70% of the nozzle; 0.75 to 1.5 times the nozzle
0.2 mmUp to 0.16 mmAbout 0.22 mmPrusa: below 80% of the nozzle; about 110% of the nozzle
0.2 mm0.04 to 0.16 mm0.18 to 0.40 mmUltiMaker Cura warning limits, one nozzle size on the printer: 0.04 mm to 80%; 0.1 mm plus 40% to 200%
0.2 mmNot stated0.20 mmE3D: width equal to the nozzle
0.25 mm0.06 to 0.15 mmNot statedUltiMaker printer specification; its smallest nozzle is 0.25 mm
0.4 mm0.08 to 0.28 mm0.30 to 0.60 mmBambu Lab: 20 to 70%; 0.75 to 1.5 times the nozzle
0.4 mmUp to 0.32 mmAbout 0.44 mmPrusa: below 80%; about 110%
0.4 mm0.04 to 0.32 mm0.26 to 0.80 mmUltiMaker Cura warning limits, one nozzle size on the printer
0.4 mm0.02 to 0.20 mmNot statedUltiMaker printer specification
0.4 mmNot stated0.40 mmE3D: width equal to the nozzle
0.6 mm0.12 to 0.42 mm0.45 to 0.90 mmBambu Lab: 20 to 70%; 0.75 to 1.5 times the nozzle
0.6 mmUp to 0.48 mmAbout 0.66 mmPrusa: below 80%; about 110%
0.6 mm0.04 to 0.48 mm0.34 to 1.20 mmUltiMaker Cura warning limits, one nozzle size on the printer
0.6 mm0.02 to 0.30 mmNot statedUltiMaker printer specification
0.6 mmNot stated0.60 mmE3D: width equal to the nozzle
0.8 mm0.16 to 0.56 mm0.60 to 1.20 mmBambu Lab: 20 to 70%; 0.75 to 1.5 times the nozzle
0.8 mmUp to 0.64 mmAbout 0.88 mmPrusa: below 80%; about 110%
0.8 mm0.04 to 0.64 mm0.42 to 1.60 mmUltiMaker Cura warning limits, one nozzle size on the printer
0.8 mm0.02 to 0.60 mmNot statedUltiMaker printer specification
0.8 mmNot stated0.80 mmE3D: width equal to the nozzle

The rules behind the numbers

  • Bambu Lab. A reasonable layer height is 20% to 70% of the nozzle diameter. Bambu Lab advises leaving the default line width alone; if you change it, keep it between 0.75 and 1.5 times the nozzle diameter. Its presets use half the nozzle diameter as first-layer height.

  • Prusa. Layer height should stay below 80% of the nozzle diameter, and PrusaSlicer refuses a layer higher than the nozzle is wide. A second Prusa article puts the maximum at 70 to 80%, because layer adhesion suffers beyond it. Extrusion width should be about 110% of the nozzle; PrusaSlicer's automatic value is 1.125 times the nozzle, which is 0.45 mm for a 0.4 mm nozzle. For a first layer that sticks better Prusa mentions 120 to 140%.

  • UltiMaker Cura. Line width defaults to the nozzle size, and Cura marks a line width below 0.1 mm plus 40% of the nozzle or above twice the nozzle with a warning. Layer height is one setting for the whole print: the warning starts below 0.04 mm and above 80% of the smallest nozzle diameter among the printer's extruders. The Cura rows therefore hold for a printer with a single nozzle size. With a 0.4 mm and a 0.8 mm nozzle fitted, the upper limit is 0.32 mm, not 0.64 mm. These are warning thresholds, not recommendations.

  • UltiMaker printers. The specification pages list a layer resolution per nozzle. Their maximum is 50% of the nozzle for 0.4 and 0.6 mm, 60% for 0.25 mm and 75% for 0.8 mm.

  • E3D. Extrusion width should correspond to the nozzle fitted, sometimes slightly reduced to fine-tune flow. E3D's pages gave us no layer-height rule.

A line can be wider than the hole it comes out of because the nozzle flattens the extra plastic. Bambu Lab adds that the line cannot become wider than the outside of the nozzle tip.

What each nozzle size is chosen for

What each nozzle size is typically chosen for

Uses and trade-offs as described on Bambu Lab, Prusa, UltiMaker and E3D pages read on 22 November 2026; the makers' descriptions, not OmniTechs test results.
NozzleChosen forTrade-offs the makers name
0.2 mm (Bambu Lab)Models with a lot of detail, such as tabletop miniaturesClogs are common; no carbon-fibre, glass-fibre or particle-filled filament; its stainless-steel nozzle is not abrasion resistant; less strength than 0.4 or 0.6 mm
0.25 mm (Prusa)Detail in the horizontal plane: small text, logos, jewellery; supports that come off easilySignificantly longer print times; higher clogging risk; not compatible with some filaments, those containing larger particles
0.4 mmThe default on most printers; Bambu Lab's second choice for fibre-filled filament, where it improves detail and surface qualityParts of small letters can be lost in slicing
0.6 mmPrints without tiny details, such as holders, racks and flower pots; Bambu Lab's first choice for fibre-filled filament, in hardened steelTiny details and text come out worse; supports are harder to remove
0.8 mmLarge parts printed fast with wide, thick linesDetail decreases as the diameter goes up; very small details cannot be printed

Three points from the sources belong with this table.

Speed. Prusa explains where the time goes: a wider line needs fewer perimeters for the same wall, for example two with a 0.6 mm nozzle where a 0.4 mm nozzle needs three, and a larger nozzle allows a higher layer. Prusa puts the gain of a 0.6 mm nozzle at up to twice the speed. A vase with a single wall prints in almost the same time with either. Bambu Lab notes that a high layer needs a slower print speed so the hot end can melt the plastic, and that its 0.2 mm nozzle is usually held to about 2 mm³/s.

Strength. In Prusa's own impact test, samples printed with a 0.6 mm nozzle absorbed up to 25.6% more energy than samples from a 0.4 mm nozzle, and samples from a 0.25 mm nozzle 3.6% less. Bambu Lab writes that most prints from its 0.2 mm nozzle have less strength than prints from a 0.4 or 0.6 mm nozzle, and gives as the reason that the very thin layer lines lead to less than ideal layer bonding. Both are the makers' own statements, one about test samples and one about a nozzle; neither is a strength rating for your part.

Filled and abrasive filament. The restrictions differ per maker and diameter. For carbon-fibre, glass-fibre and particle-filled filament, Bambu Lab says not to use its 0.2 mm nozzle because the clogging risk is extremely high, and to fit a hardened steel nozzle of 0.6 or 0.4 mm. Prusa's statement for its 0.25 mm nozzle is narrower: it is not compatible with some filaments, those containing larger particles. Prusa also says its standard brass nozzle wears too quickly with abrasive filament.

How the figures were obtained and where they stop

Each range is the maker's published rule applied to the four diameters; the products are exact to two decimals, so nothing was rounded. Three limits matter. UltiMaker lists 0.25 mm as its smallest nozzle and Prusa's article describes a 0.25 mm nozzle, not 0.2 mm, so the 0.2 mm rows for Prusa and Cura are the percentage rule applied to that diameter. The rules are general: material, print speed and the hot end's melting capacity narrow the usable range further, and a maker's figures for one printer can differ from its general rule, as the UltiMaker printer rows show. And E3D's documentation wiki could not be reached, so E3D appears with line width only.

Using the tables

  1. Find the smallest feature that lies flat: the thinnest wall or the thinnest letter stroke. Prusa is clear that nozzle size sets detail in the horizontal plane and that changing the layer height does not make text more legible.

  2. Compare that feature with the line width column. A stroke narrower than one line cannot be filled properly. How to measure letters is in design a readable custom keychain.

  3. Pick the layer height inside the range for the nozzle, by the surface you want to improve. That choice is worked out in 3D printing layer height: 0.12, 0.20 or 0.28 mm.

  4. Check the filament against the maker's page for your nozzle. The restrictions for Bambu Lab's 0.2 mm nozzle and Prusa's 0.25 mm nozzle differ, as described above.

  5. Slice and compare the estimated time in the preview. Do not derive it from the nozzle size alone.

If you have a part printed for you, the useful input is not a nozzle size but which detail must stay sharp and which face is visible. The OmniTechs service page puts it this way: you do not need to know every print setting.

Read on in 3D printing layer height, in how long a 3D print takes, with print times from our catalogue, or in design a custom keychain that stays readable.