FDM design rules side by side: what Prusa, UltiMaker, Protolabs Network, Xometry and Materialise publish
By Sina Esfahani, OmniTechs · Published 22 November 2026
Five widely used FDM design guides share one number: 45° as the overhang you can print without support. Prusa alone goes further, to 60°, and to 75° on its newest printers. On everything else they differ. The longest unsupported bridge is 5 mm at Protolabs Network and Xometry and 10 mm at UltiMaker for basic filaments (up to 25 mm with Tough PLA and tuned cooling), the minimum wall runs from 0.45 mm to 1.2 mm, and the clearance between mating parts from 0.2 mm to 0.6 mm.
Every figure on this page is that publisher's guidance for its own machines, materials and settings, read on 22 November 2026. None of them is an OmniTechs capability, tolerance or promise.
The published values, side by side
FDM design rules as published by five sources
| Feature | Prusa | UltiMaker | Protolabs Network | Xometry | Materialise (ABS-M30) |
|---|---|---|---|---|---|
| Overhang without support | 45 to 60°; up to 75° on three named printers | 45° | 45° | 45° | 45° |
| Bridge without support | Not stated | 10 mm; up to 25 mm with Tough PLA and tuned cooling | 5 mm | 5 mm | Not stated |
| Minimum wall thickness | One perimeter: 0.45 mm on a 0.4 mm nozzle | 0.5 mm | 0.8 mm | 0.75 mm supported, 1.00 mm unsupported | 1 mm; 1.2 mm for larger parts |
| Minimum hole diameter | Not stated | 2 mm | 2.0 mm | Over 1 mm | Not stated |
| Embossed text | Not stated | Not stated | Not stated | 0.8 mm thick, 0.5 mm high | Line 2.5 mm, 0.5 mm high |
| Engraved text | Not stated | Not stated | Not stated | 1.0 mm thick, 0.5 mm deep | Line 1 mm, 0.3 mm deep |
| Minimum pin diameter | Not stated | Not stated | Minimum not stated; fillet advised below 5 mm | 1 mm | Not stated |
| Clearance between mating parts | At least 0.3 mm for moving parts | 0.6 mm between parts printed together | Not stated | 0.2 to 0.3 mm for a sliding fit | 0.4 mm between parts printed together |
Notes on the columns:
Prusa writes for its own desktop printers with a 0.4 mm nozzle and PrusaSlicer. The overhang range depends on nozzle diameter and settings; with a 0.25 mm nozzle Prusa says the angle may fall below 45°. The 75° applies to the MK4S, CORE One/+ and CORE One L. Bridges are only described as short.
UltiMaker values come from an article first published in 2020. Its PDF guide "How to design for FFF 3D printing" gives no bridge length, only that shorter is better, and sets the minimum wall at the nozzle diameter or more.
Protolabs Network takes its wall and hole values from the guideline table on its FDM service page. A knowledge-base article of its own puts the minimum wall at two to three times the nozzle diameter, typically 0.8 to 1.2 mm. It gives no minimum pin: under 5 mm a pin connects weakly, so it advises a fillet at the base or an off-the-shelf pin in a printed hole.
Xometry publishes two sets. The column follows a 2025 article by its Head of Sales Engineering; the hole value comes from its FDM mini-guide, which is stricter elsewhere: 1.2 to 1.5 mm for supporting walls, and raised text at least 1 mm thick and 1 mm high. The 2025 article also lists 0.5 mm of clearance under the label "interference fit".
Materialise values apply to parts it prints in ABS-M30 with water-soluble support, an industrial service rather than a desktop printer. Its specification list gives a minimum wall of 0.8 mm, and 1.2 mm for online orders. It prefers engraved to embossed text.
Not stated means the pages read for that publisher give no number. It does not mean the feature has no limit.
The overhang rule is worded in two directions. UltiMaker and Materialise write that surfaces below 45° need support; Protolabs Network and Xometry write that overhangs above 45° do. That points to different reference lines for the angle, and at 45° both readings coincide. Before you apply Prusa's 60° or 75°, check the illustration on its page.
Why each rule exists and what to check in the slicer preview
Why each FDM design rule exists and what to check in the slicer preview
| Feature | Why the rule exists | What to check in the slicer preview |
|---|---|---|
| Overhang | Each layer rests on the one below; Protolabs Network: at 45° a new layer is supported by 50% of the previous one | Whether support is generated under the surface and where it touches a visible face |
| Bridge | Protolabs Network: nothing lies under the first bridging layer, so the material tends to sag | Which spans are printed as bridges, how long they are and whether support appears under them |
| Wall thickness | Prusa: a wall thinner than one perimeter is not printable | Whether the wall is drawn in every layer and how many perimeters it gets |
| Hole | UltiMaker: a hole that is too small fills with material; Protolabs Network: vertical holes print undersized | Whether the hole stays open in the sliced layers |
| Embossed or engraved text | Xometry: small features below the filament's thickness do not register | Whether every letter stroke is drawn as its own line or gap |
| Pin | Protolabs Network: a pin under 5 mm can consist of perimeters only and connects weakly to the part | Whether the pin has infill or only perimeters, and whether its base has a fillet |
| Clearance | Prusa: parts with zero clearance will probably not slot together, and materials can warp or shrink | Whether a gap stays visible between the two parts in every layer, including the first |
The preview shows what the printer will lay down. It does not prove that a drawn wall is strong enough or that a drawn gap stays open in the print.
How the figures were collected, and their limits
Each value was read from the publisher's own page on 22 November 2026; the pages are listed under Sources. Table 1 has 40 cells, and 14 of them are "Not stated". Nothing was filled in from other sites or from memory.
The limits matter as much as the numbers:
These are guidelines, not measurements. OmniTechs did not test them, and they say nothing about what a particular printer achieves on a particular day.
The publishers write for different equipment. Prusa and UltiMaker describe their own desktop printers. Protolabs Network and Xometry describe parts ordered through a manufacturing service. Materialise describes one material in its own production.
The pages differ in age. UltiMaker's article dates from 2020. Xometry's mini-guide dates from 2020 and was updated in 2025. The Prusa, Protolabs Network and Materialise pages show no publication date.
The values move with the set-up. Prusa ties the overhang limit to nozzle diameter and settings, Protolabs Network to the material, and UltiMaker says the minimum hole depends on material and settings.
Clearance is the least transferable row. Prusa writes in the same section that there is no single "universal" value for it. OmniTechs' own guide to 3D-printing tolerances and clearance says the same: there is no universal clearance for every print, and a number from another printer or shape is not a proven allowance for yours.
How to use the comparison
Find the column closest to your situation. If you print on your own machine, start with the printer maker's column. If you order from a service, ask that service for its own guideline.
Treat the strictest value in a row as the point where you start checking. It is not a pass mark. A feature near any of the published limits deserves a look in the preview.
Check the sliced preview with the second table before you print or send the file.
Test what has to fit. Prusa and UltiMaker both say test prints are needed when dimensions matter. Print the one connection, measure it and adjust the model.
Cite the publisher and the date when you quote a value. "The FDM rule" does not exist; five publishers give five answers for wall thickness alone.
For a connection that has to slide, clamp or come apart, continue with 3D-printing tolerances and clearance. Overhangs and bridges change with the build direction, which is the subject of choosing a 3D-print orientation. Wall thickness under load is covered in how strong 3D-printed parts are, and small holes for screws in printed threads, captive nuts and heat-set inserts. If an existing model breaks these rules and you want it fixed for you, OmniTechs can make a 3D model printable.

